OrcaSlicer Bed Type Settings: All Six Plates Explained
Open the Bed type dropdown in OrcaSlicer and you get six options. None of them says “smooth PEI” — and a smooth PEI sheet is the most common plate in the hobby. If that is what is on your printer, the setting you want is Smooth High Temp Plate, and nothing in that name tells you so.
That is the short version. Orca slicer build plate settings are the most-ignored corner of the slicer, and the Orca bed type control is doing more work than its one-line label suggests. Here is the rest of it: where the setting lives in both OrcaSlicer and Elegoo Slicer, what all six plates are for, what bed temperature to run on each, and why this dropdown changes more than a label.
Grab the reference sheet. Everything below is condensed into a three-page PDF you can keep next to the printer — all six plates, a bed temp matrix by material, and the sources behind every number. Download the OrcaSlicer bed types reference (PDF)
How to change bed type in Orca Slicer
Section titled “How to change bed type in Orca Slicer”The full orca slicer change bed type workflow is four steps:
- Open the Prepare tab.
- Find the Bed type selector near the plate in the right-hand panel.
- Pick the plate that is physically on your printer right now — not the one the printer profile shipped with.
- Re-slice.
That last step matters more than it looks, and the next section explains why.
If you want per-plate temperatures to actually apply, you also need Support multi bed types enabled in Printer Settings. With that off, the per-plate temperature fields are not in play.
How to change bed type in Elegoo Slicer
Section titled “How to change bed type in Elegoo Slicer”Elegoo Slicer is an OrcaSlicer fork, so the answer to elegoo slicer change bed type is the same answer: same control, same place on the Prepare tab, same behaviour. Anything in this post about orca slicer plate settings applies there too.
Creality Slicer is also Orca-derived, with one addition — it carries an Epoxy Resin Plate option that upstream OrcaSlicer does not have, for Creality’s double-sided epoxy-coated sheet. Creality publishes no temperature figures for it.
Orca slicer bed types: all six options
Section titled “Orca slicer bed types: all six options”| Dropdown option | What it physically is | Best for |
|---|---|---|
| Smooth Cool Plate | Low-temperature coated sheet, glossy finish | PLA at low bed temps, glossy first layers |
| Textured Cool Plate | The same coated sheet, textured finish | PLA at low bed temps, matte first layers |
| Cool Plate (SuperTack) | High-grip low-temperature surface | PLA and PETG with no glue at all |
| Smooth High Temp Plate | This is the smooth PEI plate | Glossy first layers on bare PEI |
| Textured PEI Plate | Powder-coated PEI on spring steel | The all-rounder — widest material list |
| Engineering Plate | High-temperature engineering surface | ABS, ASA, PC, PA, PA-CF |
Two things worth knowing about that list.
The two Cool Plate entries are the same surface. Smooth Cool Plate and Textured Cool Plate differ in finish only — same coating, same temperature guidance, same glue habit. Pick whichever matches the sheet in your hand and stop worrying about it.
Cool Plate (SuperTack) is a genuinely different plate, not a variant of the above. It is a high-grip surface intended to hold PLA and PETG without any glue stick at all. Clean it with warm water and detergent — not IPA.
The naming trap: your smooth PEI plate is called something else
Section titled “The naming trap: your smooth PEI plate is called something else”This is the part that trips people up, and it is why orca slicer bed type gets searched as often as it does.
Of the six options, exactly one contains the letters PEI — Textured PEI Plate. So if you have a smooth PEI sheet on your printer, you scan the list, see nothing that matches, and leave the dropdown wherever the profile put it.
The right answer is Smooth High Temp Plate. It is the smooth PEI plate. The name describes its temperature rating rather than its surface, which is technically accurate and practically useless when you are looking for the word “PEI.”
Published sources put the smooth PEI plate’s ceiling at around 120 °C, against 180 °C for the textured PEI plate. If you print a lot of high-bed-temperature materials, that difference is worth knowing independently of which dropdown entry you pick.
Why bed type is not just a label
Section titled “Why bed type is not just a label”Here is the thing most guides skip. The bed type dropdown is not cosmetic.
Every filament profile stores a separate bed temperature per plate type, with independent values for the first layer and all other layers. The dropdown decides which of those stored pairs gets written into your G-code.
Prove it to yourself in about ninety seconds:
- Slice any model. Open the G-code preview and note the bed temperature.
- Change the bed type. Nothing else.
- Re-slice. Look at the bed temperature again.
The M140 / M190 value changes. Which means if the dropdown is wrong, your first
layer is being printed at a temperature you never chose — and “my first layer won’t
stick” turns out to have been a settings problem the whole time.
This is also why there is no separate orca slicer change bed temp procedure to learn. You can override the number directly in Filament Settings, but the plate you select is what decides which stored value gets used in the first place. Fix the bed type and the temperature usually fixes itself.
Orca slicer bed temp by material
Section titled “Orca slicer bed temp by material”Here is where I have to be straight with you: the published sources do not agree, and pretending otherwise would make this post less useful, not more.
| Material | Bambu spec (Textured PEI) | OrcaSlicer wiki | Kingroon (smooth PEI) |
|---|---|---|---|
| PLA | 45–60 °C | 50–60 °C | 70 °C |
| PETG | 60–80 °C | not listed | 70 °C |
| ABS | 90–100 °C | 90–100 °C | — |
| ASA | 90–100 °C | 90–100 °C | — |
| TPU | 35–45 °C | 40–60 °C | — |
| PC | 90–110 °C | 100–120 °C | — |
| PA / Nylon | 90–110 °C | 90–110 °C | — |
Three sources, and a 25 °C spread on PLA — the most common filament there is. OrcaSlicer’s own material temperature table omits PETG entirely. ABS and ASA are the only rows where everyone agrees outright.
There is no version of this where a chart hands you the right number. Use the spread as a sanity check, then print a first-layer patch and decide by looking at it.
The glue question is equally muddled. Bambu’s own specification lists PETG as needing no adhesive on textured PEI; other guides say a glue stick is necessary there precisely because adhesion is otherwise too strong. Bambu’s Cool Plate wiki recommends a thin glue coat every two or three prints. Pick a position based on your own plates, not on a table.
A note on PETG and smooth PEI
Section titled “A note on PETG and smooth PEI”You will see it repeated everywhere that PETG bonds aggressively to bare smooth PEI — strongly enough that removing a part can take coating with it. All3DP’s guidance is that PETG, TPU and PC “can stick too strongly to smooth PEI, so a release layer may be needed.”
I have not damaged a plate this way and I am not going to show you photos of something I have not seen. What I will say is that the precaution is cheap: run PETG on textured PEI, or put a glue stick down as a release layer if you want the glossy bottom. There is no upside to finding out the hard way.
First layer settings that change with the plate
Section titled “First layer settings that change with the plate”Bed temperature is stored per plate. Most other first-layer settings are not — which means these are the ones you change by hand every time you swap:
- Z-offset — plates are not all the same thickness
- First layer flow — a textured surface has valley volume to fill that a smooth one does not
- Elephant foot compensation — behaves differently on textured vs. smooth
- First layer speed
If you own more than one plate, the honest advice is to keep a saved printer profile per plate rather than trying to remember which numbers went with which sheet.
Automating the Z-offset with start G-code
Section titled “Automating the Z-offset with start G-code”OrcaSlicer passes the selected plate to your machine start G-code as curr_bed_type,
so the offset can travel with the plate instead of being changed by hand:
{if curr_bed_type=="Textured PEI Plate"} SET_GCODE_OFFSET Z=-0.05{else} SET_GCODE_OFFSET Z=0.0{endif}The string has to match the dropdown entry exactly, including case — the same names as
the table above. The -0.05 is an example, not a value to copy: calibrate it against
your own first layer on that plate.
What if my plate isn’t in the list?
Section titled “What if my plate isn’t in the list?”For an aftermarket sheet — a third-party PEI sheet, a garolite plate, a textured spring steel that did not come with the machine — pick the option whose surface and temperature range most closely matches what you actually have, then set your bed temperature by test rather than trusting the preset. The dropdown is a starting point, not a driver.
Aftermarket plates also carry their own ratings that have nothing to do with the dropdown entry you pick. QIDI’s Cool Plate Pro, for example, publishes a 120 °C surface temperature resistance and a material list running up to PPS and PPA — a very different plate from the Bambu-lineage Cool Plate that OrcaSlicer’s entry is named after. Read your plate’s own documentation.
Sources
Section titled “Sources”Check my working. Every figure in this post is a published number from one of these, cross-checked against the others and attributed wherever they conflict.
- OrcaSlicer wiki — material temperatures — per-material bed temperature ranges, the multi bed types setting, and the per-plate first-layer fields. The slicer’s own documentation, and the source I weight highest.
- Bambu Lab Textured PEI Plate specification — per-material bed temperatures, the 180 °C ceiling, and per-material adhesive requirements. Manufacturer data, but note this link is a reseller listing of that spec table rather than bambulab.com.
- Bambu Lab wiki — printing on the Cool Plate — glue-stick cadence and cool-before-removal guidance. Publishes no temperature figures.
- 3dbite — build plates complete guide — per-plate maximum temperatures, SuperTack figures, engineering plate guidance. Independent guide; treat as a lead.
- All3DP — how to choose the right build plate — material compatibility by plate and the over-adhesion warnings. Publishes no temperature figures at all.
- Kingroon — how to choose a build plate — PLA at 70 °C on smooth PEI, and the outlier in the PLA row above.
- SainsMart — Creality epoxy resin build plate — material list for the Creality Slicer-only plate. No temperature figures.
- QIDI Cool Plate Pro — an aftermarket example with its own 120 °C rating.
None of it has been measured on your printer, and where I have tested something myself I have said so. If a number here disagrees with your machine, your machine is right.
Download the three-page reference PDF · Watch the video · More free 3D printing calculators · Free Klipper configs
No sponsored printer reviews. Ever.
