Skip to content

infill

2 posts with the tag “infill”

OrcaSlicer 2.5 Is Out: I Timed the Same Print in 2.4.2 and 2.5

OrcaSlicer 2.5 is out of alpha. Since my alpha video last week, I’ve put the release through one simple test: slice and print the exact same model in 2.4.2 and 2.5, then compare what the slicer promised against what the printer actually did.

The short version: 2.5 printed slightly faster, and its time estimate was far closer to reality. The second part is the bigger deal.

Do this first. It takes a minute.

  1. In OrcaSlicer, open Help → Show Configuration Folder.
  2. Select everything in that folder and compress it into a zip archive.
  3. Move the zip somewhere outside the OrcaSlicer folder.

If anything goes sideways after the upgrade, you can drop your printer, filament, and process profiles straight back in.

  • Model: a 60 × 60 × 60 mm cylinder. I chose it because it also shows how the seam is placed.
  • Infill: gyroid
  • Settings: the same profile in both versions
Slicer estimate Actual print time Estimate error
OrcaSlicer 2.4.2 1 h 25 min 1 h 18 min 7 min over
OrcaSlicer 2.5 1 h 15 min 1 h 16 min 1 min under

Read that table carefully. The estimates differ by 10 minutes. The actual prints differ by 2.

So 2.5 really is faster on this model, but only by about 2 minutes. The rest of that 10-minute gap is 2.4.2 overestimating its own print time. 2.5’s estimate came within a minute of the real print time.

If you quote jobs, plan prints around a schedule, or price prints by machine time, an accurate estimate is worth more than the two minutes.

The slicer’s per-feature breakdown shows where 2.5 changed things:

Feature (estimated) 2.4.2 2.5 Difference
Sparse infill 37 min 10 s 29 min 41 s −7 min 29 s
Travel 6 min 13 s 5 min 15 s −58 s

Travel: with infill hidden in the preview, the travel paths (the blue lines) in 2.5 are visibly shorter and better ordered, even on a model this simple.

Sparse infill: this is the big one. 2.5 adds a Sparse Infill Smooth Factor that rounds the corners of the infill path. That lets the toolhead hold more of its speed through turns instead of braking into every corner. Gyroid is already curvy, and smoothing makes it curvier.

Those two rows add up to about 8.5 of the 10 estimated minutes. Because the actual print was only 2 minutes faster, much of that “saving” was the old estimate being too pessimistic, not the printer finishing early. That’s still a good result. Just don’t expect a 10-minute saving on your own prints because the slicer says so.

  • The Delete key works again. In my alpha video, Delete didn’t remove selected objects. In 2.5 it does.
  • Z contouring works on multiple objects. It now behaves correctly with more than one shape on the plate.
  • Primitives take typed dimensions. Right-click → Add Primitive → Cube, and you can type the size directly instead of creating the object and then resizing it in a separate menu. I use primitives constantly for test prints, so this saves me a step every time.
  • Inward wipe at the seam. There’s a setting to have the nozzle wipe inward as it finishes a loop at the seam. I haven’t seen a visible difference in my seams yet. That’s on my tuning, not on Orca.

2.5 introduces Python plugins: a supported way to add your own features to the slicer without maintaining a fork. You can turn each plugin on or off and watch what it does to the toolpath.

I’m already using this to experiment with a custom infill pattern. One warning from experience: turn a plugin off when you’re done testing it. I left one of my tuning plugins enabled and it quietly changed a model I sliced afterward. OrcaSlicer also asks for permission before a plugin reaches outside its data folder, goes online, or launches another program. Only install plugins you trust.

Yes, once your profiles are backed up. Better estimates and faster sparse infill are worth it on their own, and the bug fixes remove some real friction from the alpha.

One caveat: this is a single model with a single infill pattern. Your time savings will depend on how much of each print is sparse infill and travel. Slice one of your own regular prints in both versions and compare.


Stop recalculating the same calibration math. Rotation distance, pressure advance, max volumetric speed, input shaping, and 20+ more calculators are free at go.minimal3dp.com.

Watch the video · Free Klipper configs · OrcaSlicer tutorials hub

No sponsored printer reviews. Ever.

Dialing in Multi-Material & Smoother Infill | OrcaSlicer 2.3.2 (Part 3)

Hey, this is Mike from Minimal 3DP. Today we are taking a closer look at OrcaSlicer 2.3.2 with three focus areas: multiline infill, spiral Z-hop, and bulletproof wipe towers.

In older slicer builds, multi-material printing can look incredible until a prime tower collapses halfway through, taking hours of print time down with it. Even with aggressive tuning, wipe towers are still fragile when you mix materials like PETG and PLA.

The latest OrcaSlicer 2.3.2 release candidates include several software-level changes designed to reduce those failures. Let us break down what matters and what to enable.

Watch on YouTube: https://youtu.be/4Pr5vlJvTvk


The Hardware Bridge: Multi-Material Testing

Section titled “The Hardware Bridge: Multi-Material Testing”

Software tweaks only work if your hardware can keep up. For this test set, we are printing K2 Plus parts for an upcoming video and using that platform as the baseline for all 2.3.2 multi-material checks.

Transparency Note: Some links in this post are affiliate links. If you use them to make a purchase, I may earn a small commission that supports M3DP. You do not pay extra.


In previous versions, multiline infill patterns like Triangles or Cubic created harsh line intersections. As the nozzle crossed previously laid paths, you would hear micro-vibrations and grinding. Over time, those repeated impacts can weaken internal structure quality.

In OrcaSlicer 2.3.2 preview mode, those transitions are rebuilt with rounded corners. Rounded path transitions keep volumetric flow more consistent and reduce abrupt extruder start-stop behavior at intersections.

The practical result is less filament grinding and smoother internal motion, especially useful with softer materials like PLA+ and PETG.

2. Bulletproof Wipe Towers (PETG/PLA Interfaces)

Section titled “2. Bulletproof Wipe Towers (PETG/PLA Interfaces)”

PETG support interfaces for PLA are popular because the materials separate cleanly. The downside is that they also struggle to bond on the prime tower, which can lead to tower delamination and mid-print failure.

OrcaSlicer 2.3.2 adds interface-specific controls to improve tower survivability:

  • Interface temperature boosts: Temperature is raised on key interface layers to improve PETG/PLA tower adhesion.
  • Extra pre-extrusion: Nozzle pressure is built before tower engagement to reduce under-extrusion on critical early layers.
  • Flushing notches: The nozzle is wiped before flushing to reduce blob dragging across the part.

These new wipe tower controls can save long prints, but there is still a cost problem: prime towers consume a lot of filament.

To quantify that waste, use the Minimal 3DP FDM Cost Calculator:

Calculate Your True Print Costs

If you are tired of typing filament and machine costs into every run, the Operator tier on Patreon unlocks Pro calculator features with saved profile data:

Join the Operator Tier on Patreon ($5/mo)

This lets you store local energy rates and machine data so you can evaluate multi-color jobs quickly before you commit print time and material.


4. Spiral Z-Hop Optimization & Klipper Config

Section titled “4. Spiral Z-Hop Optimization & Klipper Config”

Standard Z-hop can force abrupt Z-axis movement. On lower-end controller boards, large amounts of micro-movement can overload the planner buffer and cause stutters or blobs.

Spiral Z-Hop in OrcaSlicer 2.3.2 introduces adaptive slicing resolution (roughly 4 to 24 segments), producing smoother motion commands that are easier for controllers to process.

If you run mainline Klipper, validate your retraction and Z-axis limits so the machine can execute rapid hop transitions reliably:

# Minimal 3DP Z-Hop & Retraction Baseline (printer.cfg)
[firmware_retraction]
retract_length: 0.8
retract_speed: 40
unretract_extra_length: 0.0
unretract_speed: 40
[stepper_z]
# Ensure max_z_velocity and max_z_accel can support rapid spiral hops
max_z_velocity: 15
max_z_accel: 100

OrcaSlicer 2.3.2 makes meaningful progress on three real production issues:

  • Cleaner multiline infill transitions
  • More reliable PETG/PLA wipe tower behavior
  • Smoother Z-hop motion delivery for constrained controllers

These are practical quality-of-life improvements, but they do not remove the economics of multi-material waste. Pair the new slicer controls with cost tracking so your print decisions stay both reliable and profitable.