OrcaSlicer Max Volumetric Speed: Run the Max Flow Rate Test
Work out your max volumetric speed with the free calculator →
Max volumetric speed is the most plastic your hotend can melt and push out per second, in mm³/s. Set it in OrcaSlicer and the slicer will slow any move that would ask for more. Leave it wrong and you get under-extrusion, weak walls and parts that look fine until you load them.
There are two ways to find your number. I’ve used both. The OrcaSlicer test is faster; the manual test needs no slicer at all.
Where the setting lives
Section titled “Where the setting lives”In OrcaSlicer it’s a per-filament setting, because filament type, brand and temperature all change it:
- Open the Filament settings and click Edit.
- Scroll to the bottom of the first tab.
- Set Max volumetric speed.
- Save the filament profile.
It should always be set. If it’s left at a default that’s too high for your hotend, nothing limits the slicer.
Method 1: OrcaSlicer’s Max Flow Rate test
Section titled “Method 1: OrcaSlicer’s Max Flow Rate test”This prints a hollow serpentine that ramps flow up as it gets taller. You find the height where the walls start to fail and convert that height to mm³/s.
Calibrate temperature first. Max flow depends on nozzle temperature, so this test goes second in the calibration order.
- Calibration → Max flowrate.
- Set the start and end volumetric speed. The defaults are 5 to 20 mm³/s. If your hotend is rated higher, raise the end value so the test can find the limit.
- Leave the step at 0.5.
- Set brim to Auto so the thin tower stays on the bed.
- Slice and print.
- Find where the surface finish changes. That’s where the layers start to fail.
- Measure with calipers from the bottom of the print to that point.
- Enter start value, step and measured height in the calculator. It converts the height to mm³/s.
- Take 5–10% off and enter that in the filament profile.
My result: Sovol SV08 with a Micro Swiss FlowTech
Section titled “My result: Sovol SV08 with a Micro Swiss FlowTech”- Filament: tri-color silk PLA at 210 °C
- Test range: 5 to 35 mm³/s, step 0.5 (I raised the end because the FlowTech is rated well above the default 20)
- Measured to the first deformation: 48.69 mm
- Max: 5 + 48.69 × 0.5 ≈ 29.3 mm³/s
- Set in the profile: 27 mm³/s
Method 2: The manual extrusion test
Section titled “Method 2: The manual extrusion test”This is the method from Ellis’ Print Tuning Guide. It skips the slicer: you extrude filament in mid-air at rising speeds and check whether the full length comes out.
- Heat the nozzle to your normal printing temperature.
- Mark the filament 100 mm above the extruder entrance (a ruler and masking tape works).
- Send
M83for relative extrusion. - Extrude 100 mm at a slow feed rate:
G1 E100 F360is 6 mm/s. - Check the mark. If it reached the entrance, it extruded the full 100 mm.
- Raise the feed rate a step (
F420is 7 mm/s) and repeat until the mark stops short. That’s your drop-off. - Confirm the drop-off with a longer run of 200–300 mm. Klipper blocks long extrude-only moves, so raise
max_extrude_only_distancein[extruder]above your test length first, then set it back afterwards. - Convert: mm/s of filament × filament cross-section = mm³/s. The cross-section is 2.4 mm² for 1.75 mm filament and 6.37 mm² for 2.85 mm.
My result: Voron 2.4 with a Sailfish hotend
Section titled “My result: Voron 2.4 with a Sailfish hotend”- Drop-off: 8.5 mm/s of filament (9 mm/s left a small gap; at 10 mm/s the gap grew and the filament came out thick and rough)
- Max: 8.5 × 2.4 = 20.4 mm³/s
- Minus 10%: 18.36 mm³/s, entered in OrcaSlicer
Turning mm³/s into a print speed
Section titled “Turning mm³/s into a print speed”Divide your max volumetric speed by the cross-section of the line you’re printing:
max speed (mm/s) = max volumetric speed ÷ (layer height × line width)
On the Voron: 18.36 ÷ (0.2 × 0.5) ≈ 183 mm/s. Above that, the hotend can’t keep up.
Use that number for visible features. I set outer walls at or below it. Inner walls can go faster because a skipped line there doesn’t show.
Small models never reach full speed. On a Benchy, raising the outer wall from 120 to 183 mm/s didn’t change the print time at all. The toolhead spends the whole print accelerating and braking. Max speed matters on big parts with long straight moves.
Hotend reference values
Section titled “Hotend reference values”If you can’t run a test yet, start from your hotend’s typical value, then set your profile to 80–90% of it. These are starting points; your filament and temperature decide the real number.
| Hotend | Typical max flow (mm³/s) | Source |
|---|---|---|
| E3D V6 | 11 | Ellis |
| E3D V6 Volcano | 20 | Ellis |
| E3D Revo | 11 | Ellis |
| Dragon SF | 15 | Ellis |
| Sailfish | 20 | Ellis · measured 20.4 on my Voron (PLA) |
| Dragon HF | 24 | Ellis |
| Dragonfly BMO | 13 | Ellis |
| Rapido HF | 24 | Ellis |
| Rapido UHF | 30 | Ellis |
| Mosquito | 20 | Ellis |
| Mosquito Magnum | 30 | Ellis |
| Bambu X1 | 35 | Ellis |
| Micro Swiss FlowTech | — | measured ~29 on my SV08 (silk PLA, 210 °C) |
When to re-test
Section titled “When to re-test”Max volumetric speed changes whenever you change:
- the filament type, and sometimes the brand or color
- the nozzle or hotend
- the printing temperature (hotter usually means more flow)
I keep one value per filament type (one for PLA, one for PETG) and only re-test when prints show under-extrusion at speed.
Related
Section titled “Related”- Max Volumetric Speed calculator: converts the OrcaSlicer test height to mm³/s
- Max Volumetric Speed (Theory): plan print speed from a hotend’s rated flow
- OrcaSlicer calibration order: where this test fits

